Wholesale Only

Maxitrol 325-5 Regulator

Heating, Plumbing
Maxitrol Higher Capacity 325-5

325-5 with 12A39

NEW! Higher Capacity 325-5 & 325-5L

Maxitrol has upgraded the 325-5 series for 2 psi systems. The new models offer higher capacities while using the same regulator body size as the original 325-5A series. This allows the regulators to be used on a wider range of applications without needing extra space for installation.

The new 325-5 appliance regulators have a capacity of 325,000 Btu/h and replace the 325-5A. The new 325-5L line pressure regulators feature a capacity of up to 600,000 Btu/h and replace the 325-5AL. The new 325-5 and 325-5L will be available September 1, 2013.

The 325-5L series with OPDs, for 5 psi systems, also have a change in model number, but the capacities will remain the same. The 325-5AL48 is now the 325-5L48, and the 325-5AL600 is being replaced by the 325-5L600. These model number changes go into effect September 1st.

NEW Specifications for 325-5

Gases Suitable for natural, manufactured, mixed, liquefied petroleum, & LP gas-air mixutures
Approvals ANSI Z21.18 / CSA 6.3 Gas Appliance Pressure Regulators
Maximum Inlet Pressure CSA Certified 2 psi (13.8 kPa), 5 psi (34.5 kPa)
Maxitrol Tested 10 psi (69 kPa)
With Vent Limiter 12A39 5 psi (34.5 kPa) – Natural, 2 psi (13.8 kPa) – LP
Minimum Inlet Pressure CSA Certified 1 psi (6.9 kPa)
Emergency Exposure Limits Inlet side only 65 psi (450 kPa)
Maximum Individual Load Largest single appliance served by the regulator 325,000 Btu/hr
Capacity Total load of multiple appliances combined 325,000 Btu/hr
Vent Pipe Connection 3/8″ NPT
Ambient Temperature Limits -40°F to 205°F (-40°C to 96°C)

 

TracPipe CounterStrike

General Info, Heating, Plumbing

Flexible Gas Piping by OmegaFlex ®

TracPipe CounterStrike

When nature strikes—earthquakes, lightning—it can lead to deadly results. That is why corrugated stainless steel tubing (CSST) was developed to eliminate the danger of rigid gas piping. Twenty years ago, the American National Standards Institute published the first CSST product standard—ANSI LC-1. Since then, over 750 million feet of CSST has been installed in over five million homes in North America.

Unlike rigid pipe, TracPipe®Counterstrike® disperses electrical energy, and is listed by Factory Mutual for seismic resistance. Installed in tens of thousands of homes, TracPipe®Counterstrike® is the only lightning resistant CSST with the following level of proven performance:

  • TracPipe®Counterstrike® disperses electrical energy, and is listed by Factory Mutual for seismic resistance. Installed in tens of thoTracPipe®Counterstrike® has been shown to be up to 400 times more resistant to the damaging effects of electrical energy than yellow CSST.
  • Uses the same AutoFlare® fittings as standard TracPipe® CSST.
  • The most complete range of CSST sizes (3/8″- 2″) available.
  • No additional manufacturer bonding is required.
  • Lays straighter and pulls easier than yellow CSST.
  • The strength of TracPipe®Counterstrike® material makes it more crush resistant than competitive brands.
  • TracPipe®Counterstrike® has larger pipe diameters compared to competitive brands. Installers save money by using a smaller size TracPipe®Counterstrike® (ie. 3/8″ TracPipe®Counterstrike® versus 1/2″ other brand).
  • Listed to ANSI LC 1-2005, as well as Factory Mutual (FM) for seismic resistance and Underwriters Laboratories (UL) for fire resistance.

 

Maxitrol Gas Pressure Regulators

Heating, Plumbing

Lever Acting Design

Maxitrol Lever Acting Design Regulators

325 Series Regulators

The 325 series regulators are for 2 psi and 5 psi piping systems. Models available for appliance main burner or pilot applications and as line pressure regulators.

Models & Pipe Sizes

Type Model/Pipe Size PSI
Appliance 325-3 (3/8″, 1/2″)325-5A (1/2″, 3/4″, 1″)

325-7 (1 1/4″, 1 1/2″)

 10
Line Regulator 325-3L (3/8″, 1/2″)325-5AL (1/2″, 3/4″, 1″)

325-7L (1 1/4″, 1 1/2″)

 2
Line Regulator with OPD 325-3L47 (3/8″, 1/2″)325-3L48 (1/2″)

325-5AL48 (1/2″, 3/4″)

325-5AL600 (3/4″, 1″)

325-7L210D (1 1/4″, 1 1/2″)

 5

Gases

Suitable for natural, manufactured, mixed gases, liquefied petroleum gases and LP gas-air mixtures.

Blue Monster PTFE Thread Sealant

General Info, New Products, Plumbing

A rugged, general purpose PTFE Thread Seal Tape in a monstrous 1429″ Roll!

Blue Monster PTFE Thread Seal Tape

Professional-grade density and five times more tape!

Blue Monster  is not too thick and not too thin. It was developed by Mill-Rose in response to the demand for a higher-quality PTFE sealing tape that is easier to apply. Blue Monster is rugged, not flimsy like most thread seal tapes on the market. Blue Monster has not been stretched during the manufacturing process, so it is thicker and creates a more effective seal with less tape, and no need for pipe dope.

  • A new, thicker, professional-grade density
  • Monstrous roll (1/2″x1429″)
  • Seals threads effectively in more applications
  • No need for pipe dope.
  • Easier to use – no waste!
  • All purpose – use on iron, brass, copper, aluminum, stainless steel, galvanized steel, polyethylene, poly-propylene, PVC, CPVC, ABS, fiberglass and more.

Blue Monster  thread sealing tape is manufactured from PTFE resin, a polymer consisting of recurring tetrafluoroethylene monomers whose formula is (CF2-CF2)n. It is inert and compatible with a very wide range of materials. Use Blue Monster on threads made from galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, polypropylene, PVC, CPVC, ABS, fiberglass and more. It can be used on pipes carrying the following::

  • Acids, concentrated (see precautions)
  • Acids, dilute
  • Air, compressed
  • Alcohols
  • Aliphatic solvents
  • Ammonia, liquid
  • Aromatic solvents
  • Caustics, concentrated (see precautions)
  • Chlorinated solvents
  • Cutting oils
  • Diesel fuel oil
  • Ethylene glycol
  • Fatty acids
  • Gasohol
  • Glycerine
  • Heating oils
  • Hydraulic fluids
  • Hydraulic oils
  • Hydrogen, gaseous and liquid
  • Inert gases, gaseous and liquid
  • Jet fuel
  • Kerosene
  • Ketones
  • Liquid Petroleum Gas
  • Mineral oils
  • Natural gas
  • Nitrogen, gaseous and liquid
  • Petroleum solvents
  • Soap, liquid
  • Steam
  • Vegetable oils
  • Water

For a more-detailed list of chemicals compatible with Blue Monster, contact Mill-Rose.

Blue Monster  Characteristics

  • Compatible with a broad range of gases and liquids
  • Compatible with a broad range of piping materials
  • Will not harden or crack on the joints
  • Effective across a broad range of temperatures and pressures
  • Acts as a thread lubricant and anti-seize
  • Prevents electrolytic corrosion of threads
  • No curing time
  • Unlimited shelf life
  • Non-flammable
  • Non-toxic
  • Clean

Do not use Mill-Rose Blue Monster  Thread Sealing Tape on oxygen lines! Mill-Rose recommends Green Oxygen Tape for oxygen lines.

Note: Mill-Rose Blue Monster  Tape is compatible with most gases, but for gas lines, Mill-Rose 3-Wrap Yellow Gas Seal Tape is recommended.

Download Specification Sheet

Lucas Milhaupt Sil-Fos 15 Rings

New Products

Sil-Fos 15 Rings Verified Strong & Tight

Lucas Milhaupt Sil-Fos 15 Rings

Lucas Milhaupt Sil-Fos 15 Rings

For brazing copper tubular components… and sealing them tight!

Sil-Fos® Rings are a brazing alloy composed of 15% Silver (Ag), formed into rings to fit inside the flared fitting used to join copper tubing and fittings (commonly used in HVAC/R systems). When properly heated, the rings create a tight, leak proof joint.

  • Easy-To-Use – Just insert the pre-sized ring into the fitting for hands free brazing.
  • Visual Verification – You can SEE when you’ve drawn the brazing material evenly through the joint – no guessing whether the job is done right!
  • Joint Quality – You’re able to achieve more consistent and repeatable braze joint quality.
  • Less Waste – Wire sizes are calculated to apply the precise amount of braze alloy for each tube size.
  • Lower Cost – Saving time and materials saves you money!
  • Inventory Control – Allocate only what is needed per job.
Easy 4-Step Process

Easy 4-Step Process

Tubing OD Part # Rings/Pkg
1/4" 98700 25
3/8" 98701 25
1/2" 98702 25
5/8" 98703 25
3/4" 98704 25
7/8" 98705 25
1-1/8" 98706 10

The Sharkbite Connection System

Plumbing

Lighting Fast. Won’t Let Go.

The SharkBite Connection System

The SharkBite Connection System

The SharkBite® Connection System from Cash Acme makes any plumbing project fast and easy.

Whether you need to repair a broken pipe or plumb a whole house, SharkBite is the push-fit solution for leak-free results. The system includes hundreds of products – dozens of fittings, a wide range of push-fit valves, even PEX tubing. Tested, proven, certified – SharkBite is your connection for plumbing project success.

Cut. Push. Done.

Measure and mark your pipe, cut it clean and push it home – that’s really all you need to know.

SharkBite Installation

SharkBite Installation

SharkBite Installation

Ensure pipe is cut square and rough edges and debris are removed. Push pipe and fitting together to a 1″ depth for permanent joints with Copper, CPVC and PEX.

SharkBite Disassembly

SharkBite Disassembly

Easy Disassembly

Make a mistake? No problem with SharkBite. Disassembly is fast and easy using a simple disconnect tool.

Push-Fit Products to Get The Job Done

New Construction

Cut. Push. Done. The SharkBite® Connection System is the fastest, easiest way to plumb any residential or commercial job.

Wet or Dry Repairs

There’s no faster way to make a repair – wet or dry. Connect copper, CPVC or PEX pipe in any combination.

Water Heaters, Valves & More

Connect a water heater or shower valve. Install a mixing valve or pressure regulator – it’s all a breeze with SharkBite® push-fit connections.

Hydronic Heating Systems

Under the floor or behind a wall, a broad range of SharkBite® push-fit fittings and PEX products gives you confident connections.

S-Line Series On-Demand Water Heater

Plumbing, Water Heaters
S-Line Series On-Demand Water Heater

S-Line Series On-Demand Water Heater

About The Quietside ODW (On-Demand Water Heater)

  • Ever taken a cold shower?
  • Ever wanted to spend an extra 5 minutes in the shower but the water is getting colder?
  • Ever wanted to reduce your gas utility bill?

Now you can with the Quietside Tankless Water Heater.

Quietside tankless water heaters are Energy Star approved and one of the leaders in condensing tankless water heaters sold in North America. Conceived 5 years ago, and refined through a rigorous testing program, these tankless water heaters are at the pinnacle of performance and efficiency, producing at 12% higher efficiency than even the current Energy Star standard tankless water heaters. Quietside tankless water heaters qualify for many State Utility rebates and the new Federal Energy Tax Credit Program allowing up to 30% of the installation cost (maximum $1,500.00) as a tax credit in 2009 & 2010. High efficiency is only one of the benefits.

Quietside’s ODW Energy Start approved water heater provides on demand water heating with exceptional efficiency due to the innovative use of the S line heat exchangers. With the simple twist of a faucet this unit can provide from 0.7 to over 7 plus GPM (45 degree F temperature rise) of controlled hot water delivered at exactly the temperature required for the perfect shower.

The S line heat exchangers allow the unit to operate at above 90% efficiency, easily surpassing the minimum standard for IRS tax rebates and allowing the use of PVC venting materials due to the extremely low flue gas temperature. A self-diagnostic microprocessor controls unit operation to provide a stable delivered water temperature, and the easy to use keypad control allows the user to select from a wide temperature range to exactly match their requirements.

Available capacities: 99,000 / 120,000 / 180,000 / 199,000 BTU

To learn more call Joe today at 502-589-9287